Ideas

Drain Cover Ideas in the Philippines: 6 Steel Matting Covers for Canals, Sumps and Gutters

By Una Wire Products Inc. ·November 2026 ·5 min read
Quick Answer

Can you make a drain cover from steel matting?
Yes, for light duty. A matting panel on an angle bar seat covers a canal, sump or trench, keeps out leaves and rubbish and lets water through. Use 2×2 inch mesh in 4.5 to 5.5 mm wire, galvanized, for foot traffic. Steel matting is not a rated vehicle grating: where cars or trucks drive over, ask your engineer for a designed grating. We supply the matting, and the frame and the load check come from your fabricator.

Looking for a drain, canal or sump cover that is cheaper than a cast grating and lets water through? Steel matting panels are a simple way to cover open drains beside a house, shop or yard. This page shows six cover ideas, which mesh and wire suit each one, what the matting costs, and what to tell us so we can supply the panels. We make the matting. The frames, seats and any load check come from your fabricator or engineer.

Illustration of four steel matting drain covers: canal cover, sump cover, trench cover across a walkway and gutter guard
Four steel matting drain covers (illustration).

6 Steel Matting Drain Cover Ideas

1. Open canal cover for walkways

Lift-out matting panels resting on an angle bar seat along the canal edge, for foot traffic beside a house or shop. Keep each span short (a canal about 50 cm wide is a typical size) and use 4.5 to 5.5 mm wire. One 4×8 ft sheet (1.22 m × 2.44 m) cuts four panels of 0.5 × 1.2 m.

2. Sump and catch basin cover

A square frame with a matting panel and a lift handle keeps leaves and rubbish out of a sump or catch basin. Cut a notch if a pipe passes through. One 4×8 ft sheet cuts eight panels of about 0.6 × 0.6 m.

3. Trench cover across a walkway or shop front

A panel set flush with the floor over a shallow trench, with a flat bar edge so nobody trips on it. Paint it a visible colour, and make it removable so you can clean the trench.

4. Lift-out panels with handles

Keep each panel small enough for one person to lift, about 1 m long, with two welded loops or cut slots so a hook can lift it. Heavy fixed covers do not get cleaned.

5. Roof gutter guard

A strip of fine mesh over the gutter keeps leaves out. Use galvanized 1×1 inch matting, or chicken wire (4 ft high, 90 ft roll, ₱1,600), and slope it so leaves slide off. 2×2 inch mesh lets small leaves through.

6. Site safety cover for small openings

A framed matting panel over a small sump pit or inspection hole stops people stepping in. It is for people, not loads or vehicles, so mark it clearly. For floor openings on a construction site, ask your safety officer for the cover you must use.

Which Mesh and Wire for a Drain Cover?

CoverMesh openingWireNotes
Walkway canal cover2×2 inch4.5 – 5.5 mmGalvanized, angle seat, short span
Sump or catch basin cover2×2 inch4.5 mmLift handle
Trench cover2×2 inch4.5 – 5.5 mmFlush edge, visible colour
Lift-out panel2×2 inch4.5 mmLight enough for one person
Gutter guard1×1 inch2.6 mmOr chicken wire, slope it
Safety cover2×2 inch4.5 mmPeople only, mark it

Load capacity depends on span, wire, frame and seating. Matting covers are for foot traffic. For any place where vehicles pass, ask your engineer. See the wire mesh gauge guide.

What the Matting Costs for a Cover

Only the matting is priced here. Using our October 2026 pick-up prices for 2×2 inch black iron unless stated:

CoverSheet usedMatting, black ironMatting, galvanized
Four canal covers 0.5 × 1.2 m, 4.5 mmOne 4×8 ft sheet, cut in four₱803about ₱964 – ₱1,084
Four canal covers 0.5 × 1.2 m, 5.5 mmOne 4×8 ft sheet, cut in four₱1,122about ₱1,346 – ₱1,515
Eight sump covers 0.6 × 0.6 m, 4.5 mmOne 4×8 ft sheet, cut in eight₱803about ₱964 – ₱1,084
Gutter guard strips, 1×1 inch, 2.6 mmOne 4×8 ft sheet, cut in strips₱1,250Ask for a quote

Angle bar frames, seats, handles, paint or galvanizing and welding labour are extra. Galvanizing adds about 20 to 35%. For other gauges, see the steel matting price list.

Tips for Building a Better Drain Cover

  • Give it a proper seat. A panel that rests on an angle bar around the whole edge is much stronger than one resting on two points.
  • Keep spans short. If the canal is wide, add a center support or use two panels end to end.
  • Use galvanized. Drains are wet all year, and black iron rusts quickly. See galvanized vs black iron.
  • Keep it flush and safe. A cover that sits higher than the floor is a tripping hazard, and a cover with sharp ends can cut a foot. Border the panel with flat bar.
  • Clean it. Lift the panels and clear silt before the rainy season.

Frequently Asked Questions

Can steel matting be used as a drain cover?

Yes, for foot traffic. Rest a framed steel matting panel on an angle bar seat around the opening.

What wire thickness is best for a canal cover?

For a walkway canal cover, 2×2 inch mesh in 4.5 to 5.5 mm wire, galvanized, on a short span.

Can cars drive over a steel matting drain cover?

Steel matting is not sold as a vehicle-rated grating. For any driveway or crossing, ask your engineer for a designed cover.

Should a drain cover be galvanized or black iron?

Galvanized. Drains stay wet and black iron rusts quickly. If you use black iron, paint it and repaint when the paint wears off.

Can you cut steel matting to the size of my canal?

We make custom sheet sizes. Send us the width and length of the covers you need.

See also what wire mesh is used for in construction, the thickness chart, custom steel matting and all steel matting uses.

Send us your canal size, we quote the covers

Tell us the width and length of the opening, the mesh opening, the wire thickness and whether you want black iron or galvanized. We will reply with the price and what is in stock.

Get a Free Quote →
Need steel matting? Una Wire Products Inc. manufactures to standard and custom sizes. Request a free quote →

Where to next?

Ready to order? Get a quote or call (02) 8260-0181.

Viber