Ideas

Wire Mesh for Shotcrete and Slope Protection in the Philippines: 6 Uses of Steel Matting

By Una Wire Products Inc. ·November 2026 ·6 min read
Quick Answer

Can steel matting be used for shotcrete and slope protection?
Yes. Welded steel matting is used as reinforcement in shotcrete (sprayed concrete) slope facing, in lined canals and ponds, and for welded-mesh gabion baskets. These are engineered uses: your geotechnical or civil engineer sets the wire diameter, the mesh opening, the laps and the anchors. We supply the matting to the specification you give us, in 4×8 or 6×20 ft sheets, black iron or galvanized.

Slopes beside roads, driveways and building platforms erode and slip in the rainy season, and a concrete skin on mesh is one way to protect them. Steel matting is easy to unroll, pin and lap over a slope, and large 6×20 ft sheets cover ground quickly. This page shows six uses, typical mesh sizes, what the matting costs and what to tell us so we can quote. We make the matting. The design, anchors and drainage must come from your engineer.

Illustration of four engineered uses of steel matting: shotcrete slope facing, retaining wall facing, canal lining and gabion basket
Four engineered uses of steel matting on slopes and channels (illustration).

6 Steel Matting Uses for Slopes and Channels

1. Shotcrete slope facing

On a cut slope beside a road, driveway or building platform, matting is pinned to the slope with anchors and then covered with sprayed concrete. The mesh holds the shotcrete in place and spreads cracking. 6×20 ft sheets (1.83 m × 6 m) cover more ground with fewer joints. Your engineer sets the anchors, the drainage holes and the thickness.

2. Retaining wall facing and gabion-style baskets

Matting reinforces the concrete facing of a small retaining wall, or is formed into welded-mesh baskets that are filled with stone. Gabion mesh is usually heavier wire in a coarse opening, so tell us the panel size, opening and wire and we will quote it. Forming and filling the baskets is done on site.

3. Canal and drain lining

A thin concrete lining on a roadside canal, irrigation ditch or drain, reinforced with matting. Lay the sheets along the channel, lap them and cast or spray the lining. A lined bank erodes less than bare soil.

4. Farm pond and reservoir lining

Small farm ponds, tanks and ground-level reservoirs can be lined with mesh-reinforced concrete to control cracking as the ground moves. The wire and the thickness come from your engineer.

5. Embankment and road shoulder protection

Where a road shoulder or a driveway edge is eroding, a concrete skin on mesh can protect it. The slope angle and the drainage matter more than the mesh, so have an engineer look at the site.

6. Small private slope or terrace

For a small slope below a house or driveway, a mesh-reinforced concrete skin can protect against surface erosion. Even small slopes can fail, so have the slope checked before you build on or below it.

Typical Mesh and Wire for Slope Work

UseMesh openingWireNotes
Shotcrete slope facing4×4 or 6×6 inch3.5 – 5.5 mm6×20 ft sheets, engineer specifies
Gabion-style baskets2×2 to 4×4 inchHeavier wireTell us the panel size and wire
Canal lining4×4 or 6×6 inch2.6 – 3.5 mmLapped sheets
Pond or reservoir lining4×4 inch3.5 – 4.5 mmEngineer specifies
Embankment skin4×4 or 6×6 inch3.5 – 4.5 mmCheck slope and drainage
Small private slope4×4 inch3.5 – 4.5 mmHave the slope checked

Slope work depends on soil, water and slope angle. These are typical sizes for discussion, not designs. Your geotechnical or civil engineer must design the slope, the anchors and the drainage. See the wire mesh gauge guide.

What the Matting Costs for a Slope

Only the matting is priced here, for black iron at our October 2026 pick-up prices. One 6×20 ft sheet is 6 m × 1.83 m, about 11 m² before laps. The number of sheets you need depends on the laps your engineer specifies.

AreaSheets usedMatting, black ironMatting, galvanized
100 m² facing, 6×6 inch, 2.6 mmTen 6×20 ft sheets₱4,160about ₱4,992 – ₱5,616
100 m² facing, 4×4 inch, 2.6 mmTen 6×20 ft sheets₱6,170about ₱7,404 – ₱8,330
100 m² facing, 6×6 inch, 6.0 mmTen 6×20 ft sheets₱16,560about ₱19,872 – ₱22,356
100 m² facing, 4×4 inch, 6.0 mmTen 6×20 ft sheets₱25,130about ₱30,156 – ₱33,926

Anchors, shotcrete or concrete, drainage, labour and delivery are extra. Galvanizing adds about 20 to 35%. For a project, send us the area and the specification and we quote the matting. For other gauges, see the steel matting price list and delivery.

Tips for Slope and Channel Work

  • Get the engineer first. The anchors, thickness, drainage and slope angle come from a site check, not from the mesh.
  • Plan the drainage. Weep holes and drains matter, because water pressure behind a concrete skin is what makes slopes fail.
  • Lap and tie. Overlap sheets by the lap your engineer specifies and tie them together so they act as one grid.
  • Keep the mesh off the soil. Hold it a few centimetres from the surface with spacers so the concrete wraps it.
  • Handle safely. 6×20 ft sheets are heavy and cut ends are sharp. Use gloves and enough hands.

Frequently Asked Questions

Can you supply wire mesh for shotcrete?

Yes. Send us the wire diameter, the mesh opening and the area, and we will quote the matting in 4×8 or 6×20 ft sheets.

What mesh is used for shotcrete slope facing?

Your engineer sets it. Common choices are 4×4 or 6×6 inch mesh in 3.5 to 5.5 mm wire. We make 1×1, 2×2, 4×4 and 6×6 inch mesh.

Can you make mesh for gabion baskets?

We make welded mesh panels to the sizes you specify. Tell us the panel size, the opening and the wire. The baskets are formed and filled on site.

Is galvanized matting needed for slope work?

Galvanized matting is common where the mesh is exposed or the water is aggressive, and it adds about 20 to 35% to the cost. Your engineer decides.

Do you deliver to my site?

Tell us the site and the quantity and we will confirm delivery and timing. See our delivery page for Metro Manila lead times.

See also what wire mesh is used for in construction, steel matting sizes, custom steel matting and all steel matting uses.

Send us your area and spec, we quote the matting

Tell us the area, the mesh opening, the wire thickness your engineer specified and whether you want black iron or galvanized. We will reply with the price and what is in stock.

Get a Free Quote →
Need steel matting? Una Wire Products Inc. manufactures to standard and custom sizes. Request a free quote →

Where to next?

Ready to order? Get a quote or call (02) 8260-0181.

Viber