Ideas

Steel Matting for Septic Tanks, Precast Concrete and Stairs: 7 Uses of Welded Wire Mesh in Small Concrete Jobs

By Una Wire Products Inc. ·November 2026 ·6 min read
Quick Answer

Where is steel matting used in precast and small concrete work?
Steel matting reinforces thin concrete pieces such as septic tank and cistern cover slabs, precast panels, stepping slabs, drain box lids and canal lining. The welded grid holds its shape in the mould and spreads cracking. Use 2×2 or 4×4 inch mesh in 3.5 to 4.5 mm wire for light pieces. It does not replace the main bars your engineer specifies for beams, columns, stairs and heavily loaded slabs.

Steel matting does more than floor slabs. It also goes into many small concrete jobs where a thin piece needs a grid of steel that is quick to place and does not move during the pour. This page shows seven small concrete uses, which mesh and wire suit each, what the matting costs, and what to tell us so we can supply the sheets. We make the matting. The design, bars and spacing come from your engineer. For floors and driveways, see our concrete reinforcement guide.

Illustration of four small concrete jobs using steel matting: septic tank cover slab, stepping slabs, canal lining and concrete stairs
Four small concrete jobs that use steel matting (illustration).

7 Small Concrete Jobs That Use Steel Matting

1. Septic tank and cistern cover slabs

Cast the cover slab with a layer of matting set at mid-depth on spacers, so the mesh sits inside the concrete and not on the bottom of the form. The manhole opening needs extra bars around it, and your engineer decides how many. One 4×8 ft sheet (1.22 m × 2.44 m) cuts two pieces of 1.2 × 1.2 m.

2. Stepping slabs, pavers and garden panels

Mould thin slabs with a piece of matting cut to fit. Keep the mesh away from the edges and the surface so concrete covers it fully. One 4×8 ft sheet cuts eight pieces of 0.6 × 0.6 m.

3. Light precast panels

Planter boxes, decorative screens, wall caps and similar non-structural pieces can use matting as their reinforcement. Tall panels or wall panels that carry load need bars from your engineer.

4. Drain box and small culvert lids

Thin lids for drain boxes and small culverts. The span and the load, foot or vehicle, decide the wire and the thickness. For any lid that vehicles drive over, your engineer designs the reinforcement.

5. Canal and ditch lining

A thin concrete lining on a roadside drain, irrigation canal or ditch bank, reinforced with matting to control cracking. 6×20 ft sheets (1.83 m × 6 m) lay quickly along the channel. Cut them to the channel shape and lap them.

6. Concrete stairs and landings (secondary steel)

Matting is sometimes used as secondary reinforcement in thin stair flights and landings, in addition to the bars your engineer specifies. Do not use it in place of the main bars.

7. Crack control in plaster and topping

A strip of mesh over a beam-to-wall joint, or a sheet in a thin topping over an old slab, helps control cracks. Fix it with nails or anchors and cover it with plaster or topping. Chicken wire is also used as plaster lath.

Which Mesh and Wire for Small Concrete Jobs?

JobMesh openingWireNotes
Septic tank or cistern cover slab2×2 or 4×4 inch3.5 – 4.5 mmEngineer sets bars around openings
Stepping slabs and pavers2×2 inch2.6 – 3.5 mmKeep the mesh covered
Drain box and culvert lids2×2 or 4×4 inch4.5 – 5.5 mmSpan and load set by engineer
Canal lining4×4 or 6×6 inch2.6 – 3.5 mm6×20 ft sheets, lapped
Stairs and landings2×2 or 4×4 inch3.5 – 4.5 mmSecondary steel only
Plaster and topping2×2 or 4×4 inch2.6 – 3.5 mmFix first, then cover

These are common uses, not structural designs. Your engineer decides bar sizes, mesh, cover and spacing. See the steel matting vs deformed bar guide and the wire mesh gauge guide.

What the Matting Costs for Small Concrete Jobs

Only the matting is priced here. Using our October 2026 pick-up prices for black iron:

JobSheet usedMatting, black ironMatting, galvanized
Two cover slabs 1.2 × 1.2 m, 2×2 inch, 4.5 mmOne 4×8 ft sheet, cut in two₱803about ₱964 – ₱1,084
Eight stepping slabs 0.6 × 0.6 m, 2×2 inch, 3.5 mmOne 4×8 ft sheet, cut in eight₱534about ₱641 – ₱721
Canal lining 6 m long × 1.8 m wide, 6×6 inch, 2.6 mmOne 6×20 ft sheetfrom ₱416about ₱499 – ₱562
Canal lining 6 m long × 1.8 m wide, 4×4 inch, 2.6 mmOne 6×20 ft sheetfrom ₱617about ₱740 – ₱833

Cement, sand, gravel, forms, bars, spacers and labour are extra. Black iron is the usual choice for steel buried in concrete, and galvanizing adds about 20 to 35%. For other gauges, see the steel matting price list.

Tips for Better Small Concrete Work

  • Lift the mesh. Set it on chairs or spacers so it sits inside the concrete. Mesh lying on the bottom of the form does nothing.
  • Cover it fully. Keep the mesh clear of the edges and the surface so concrete covers every wire.
  • Lap the sheets. Overlap sheets by the lap your engineer specifies, and tie them together.
  • Cut to the form. Cut the matting to the form before you place it, and wear gloves and eye protection. We also make custom sheet sizes. See custom steel matting.
  • Cure the concrete. Keep thin pieces damp for several days, so they gain strength and do not crack.

Frequently Asked Questions

Can steel matting be used in a septic tank cover?

Yes, as reinforcement in a cover slab, with extra bars around the manhole. Your engineer decides the bars and the thickness.

Can steel matting replace rebar in stairs?

No. Matting can add secondary reinforcement, but the main bars come from your engineer.

What mesh is used for canal lining?

Often 4×4 or 6×6 inch mesh in 2.6 to 3.5 mm wire in 6×20 ft sheets. Your engineer sets the final specification.

Should steel matting for concrete be black iron or galvanized?

Black iron is the usual choice for steel buried in concrete. Galvanized costs more, so ask your engineer whether the job needs it.

Can you cut steel matting to the size of my form?

We make custom sheet sizes. Send us the width and length you need.

See also the concrete reinforcement guide, steel matting specs, steel matting calculator and all steel matting uses.

Send us your piece size, we quote the sheets

Tell us the size of the piece, the mesh opening, the wire thickness your engineer specified and whether you want black iron or galvanized. We will reply with the price and what is in stock.

Get a Free Quote →
Need steel matting? Una Wire Products Inc. manufactures to standard and custom sizes. Request a free quote →

Where to next?

Ready to order? Get a quote or call (02) 8260-0181.

Viber