Can you make a gate from steel matting?
Yes. The usual design is a steel frame (angle bar or square tube) with a steel matting panel welded or bolted inside it. The frame carries the weight and the hinges, and the matting fills the gap. It looks like a clean grid, lets air and light through, and costs less than a bar-and-picket gate. For outdoor gates use galvanized matting, or paint black iron well, and pick a 2×2 inch mesh in 2.6 to 3.5 mm wire for most homes.
Looking for a main gate, sliding gate, swing gate or farm gate design that is strong, open and affordable? A steel gate with welded wire (steel matting) infill is a simple option. The grid is rigid, lets air and light through, and is cheaper than a bar-and-picket or solid steel gate. This page shows seven gate designs, what mesh and wire suits each one, what the matting costs, and what to tell us so we can supply the panel. We make the matting. The frame, hinges and welding come from your welder or fabricator.
7 Steel Matting Gate Design Ideas
1. Single-leaf pedestrian gate
A walk-in gate beside a driveway or at a side entrance, about 0.9 to 1.2 m wide. One 4×8 ft sheet (1.22 m × 2.44 m) can be cut into two or three leaves of this size. 2.6 mm wire in 2×2 inch mesh is enough for a light gate. Add a flat bar border so the cut wire ends are hidden.
2. Double-leaf swing gate for a driveway
The classic car gate: two leaves that swing open from the posts. A 4 m opening needs two 2 m leaves. The 6×20 ft sheet (1.83 m high, 6 m long) cuts into leaves that match a standard 6 ft high fence. Keep the frame in 2 inch square tube or heavier, because a wide leaf is what sags first, not the matting. Heavier wire (3.0 to 3.5 mm) gives a stiffer panel for tall or wide leaves.
3. Sliding gate
A sliding gate runs along a track and needs clear space beside the opening equal to the gate width, but no swing room. Matting makes the leaf lighter than a solid sheet gate or a heavy picket gate, which is easier on the rollers and the motor if you add one. Use the lightest wire that gives the panel the stiffness you want, and ask your fabricator to check the roller and track rating.
4. Matting panel with a solid lower section
For privacy and safety, use a solid plate or board on the lower part of the gate and the matting on top. It keeps dogs and small children in, hides what is behind the gate, and still lets air through the upper half. A common split is the lower third solid and the upper two thirds matting.
5. Tight-mesh security gate
For a warehouse, shop or yard, use a smaller opening so a hand or foot has less to grip. We make 1×1 inch mesh (₱1,250 to ₱2,550 per 4×8 ft sheet in black iron, October 2026) and 2×2 inch is the common step up. Read about our anti-climb fence for the tight-mesh option. A tighter mesh costs more per sheet, so use it on the gate and the lowest part of the fence only if you need to.
6. Farm, pen and field gate
For pig pens, poultry runs and farm entrances, a simple frame with 2.6 mm matting in 4×4 inch mesh keeps animals in at a lower cost. Make the frame from galvanized pipe so it survives mud and moisture, and fix the hinges well, because animals lean on the gate.
7. Gate that matches a steel matting fence
If your fence is already steel matting, make the gate from the same mesh and wire so it looks like part of the fence. Order the gate panel in the same wire and finish as the fence, and paint the frame the same colour as the fence posts.
Which Mesh and Wire for a Gate?
| Gate | Mesh opening | Wire | Notes |
|---|---|---|---|
| Pedestrian gate | 2×2 inch | 2.6 – 3.0 mm | Light panel, border it with flat bar |
| Driveway swing gate | 2×2 inch | 3.0 – 3.5 mm | Stiffer panel, strong frame and hinges |
| Sliding gate | 2×2 inch | 2.6 – 3.0 mm | Keep the leaf light, check the roller rating |
| Security gate | 1×1 or 2×2 inch | 2.6 – 4.0 mm | Tight mesh costs more per sheet |
| Farm or pen gate | 4×4 inch | 2.6 – 3.5 mm | Galvanized frame, strong hinges |
These are design suggestions, not engineering specifications. Ask your fabricator or engineer to confirm frame size and hinge capacity for your gate width and weight. See the wire mesh gauge guide.
What the Matting Costs for a Gate
Only the matting is priced here. Using our October 2026 pick-up prices for 2×2 inch black iron:
| Gate | Sheet used | Matting, black iron | Matting, galvanized |
|---|---|---|---|
| 4 ft high leaf, 2.4 m wide, 3.0 mm | One 4×8 ft sheet | ₱450 | about ₱540 – ₱608 |
| 6 ft high double gate, 5 m wide, 2.6 mm | One 6×20 ft sheet, cut | ₱1,122 | about ₱1,346 – ₱1,515 |
| 6 ft high double gate, 5 m wide, 3.5 mm | One 6×20 ft sheet, cut | ₱1,871 | about ₱2,245 – ₱2,526 |
The frame, hinges, latch, paint or galvanizing, wheels and track, welding labor and delivery are extra, and they are usually most of the gate cost. Galvanizing adds about 20 to 35%. For other gauges, see the steel matting price list.
Tips for Building a Better Gate
- Frame first, matting second. Size the frame to the opening, then cut the matting to fit inside it. We make custom sheet sizes, so you can order the panel at the size you need. See custom steel matting.
- Add a diagonal brace. A brace from the bottom hinge corner to the top latch corner stops a swing gate from sagging.
- Hide the cut ends. Border the panel with flat bar or angle, and paint or galvanize any cut edge of black iron matting.
- Use galvanized outdoors. Black iron rusts quickly in rain and humidity. Galvanized matting lasts about 10 to 20 years in the Philippine climate. See galvanized vs black iron.
- Plan the posts. Gate posts carry far more load than fence posts. Make them larger and set them in concrete.
Frequently Asked Questions
Can steel matting be used for a gate?
Yes. Weld or bolt a steel matting panel inside a steel frame. The frame carries the load and the hinges, and the matting is the infill.
What size steel matting is best for a gate?
For most homes, 2×2 inch mesh in 2.6 to 3.5 mm wire. Use 4×8 ft sheets for a gate up to 1.22 m high, or 6×20 ft sheets for a 6 ft high gate.
Should a gate use black iron or galvanized steel matting?
Galvanized for any gate exposed to rain. If you use black iron, paint it well and repaint when the paint wears off.
Can you cut steel matting to the size of my gate?
We make custom sheet sizes. Send us the width and height of the panel you need. You can also cut standard sheets yourself, then paint or galvanize the cut edges.
Do you make the whole gate?
We make and supply the steel matting. Ask your welder or fabricator for the frame, hinges and installation.
See also the steel matting fence guide, other uses of steel matting, the thickness chart and our fence wire guides.
Send us your gate size, we quote the panel
Tell us the gate width and height, the mesh opening, the wire thickness and whether you want black iron or galvanized. We will reply with the price and what is in stock.
Get a Free Quote →