Can you use steel matting for display racks and market stalls?
Yes. Matting panels make strong, light wall grids, shelves and booth walls that hold hooks, baskets and signs. Use 2×2 inch mesh in 3.0 mm wire for most displays and 1×1 inch for small items. Paint it in your brand colour, or use galvanized for an outdoor market stall.
Looking for a display that is strong, light and cheaper than shop-fitting panels? A wire grid lets you hang goods from hooks anywhere on the panel, change the layout in minutes and take it down for the next bazaar. This page shows six display ideas for shops, booths and market stalls, which mesh and wire suit each one, what the matting costs, and what to tell us so we can supply the panels. We make the matting. The frames and stands come from your fabricator or carpenter.
6 Steel Matting Display and Stall Ideas
1. Wall grid display panel
A framed panel fixed to the wall holds hooks, shelves, baskets and hanging goods. Hooks go anywhere on the grid, so you can change the layout whenever the stock changes. Paint it white, black or a brand colour. A 4×8 ft sheet (1.22 m × 2.44 m) cuts to a wall panel in one piece.
2. Market stall shelves and table
A frame with tiered mesh shelves for vegetables, dried fish, snacks or fruit. The mesh lets air through and lets water drain, and it hoses clean. Use galvanized, 2×2 inch mesh in 3.0 mm wire, and add a lip so goods do not roll off.
3. Signage frame and menu board
A mesh panel makes a light backing frame for a sign: fix a printed board or tarpaulin to the mesh with cable ties, or clip menu cards onto it. It is easy to take down and store.
4. Hanging baskets and bin displays
Form mesh into baskets or bins for produce, toys, phone accessories or small goods, and hang them from the frame or set them on the shelf. Use 2×2 inch mesh, or 1×1 inch for small items, with a flat bar border on the edges.
5. Pop-up booth wall
Three framed panels hinged or clipped together make a booth back and sides that stand on their own and fold flat for transport. Panels of 1.22 m width are easy to carry and fit in a van.
6. Sari-sari store counter and window guard
A matting panel on the counter front or window keeps goods safe while customers can see in and pass money and goods through a service opening. Use 2×2 inch mesh in 3.0 mm or heavier wire.
Which Mesh and Wire for a Display?
| Display | Mesh opening | Wire | Notes |
|---|---|---|---|
| Wall grid panel | 2×2 inch | 3.0 mm | Fix to the wall every 40 – 50 cm |
| Market stall shelves | 2×2 inch | 3.0 – 3.5 mm | Galvanized, add a lip |
| Signage frame | 2×2 inch | 2.6 – 3.0 mm | Fix signs with cable ties |
| Baskets and bins | 1×1 or 2×2 inch | 2.6 – 3.0 mm | Flat bar border |
| Booth wall panels | 2×2 inch | 3.0 mm | Framed, hinged or clipped |
| Counter or window guard | 2×2 inch | 3.0 – 3.5 mm | Leave a service opening |
Hook and shelf loads depend on the frame, wire and span. Ask your fabricator to check the display for the weight of your goods. See the wire mesh gauge guide.
What the Matting Costs for a Display
Only the matting is priced here. Using our October 2026 pick-up prices for 2×2 inch black iron unless stated:
| Display | Sheet used | Matting, black iron | Matting, galvanized |
|---|---|---|---|
| Wall grid panel 1.22 × 2.44 m, 3.0 mm | One 4×8 ft sheet | ₱450 | about ₱540 – ₱608 |
| Four market stall shelves 0.6 × 1.2 m, 3.0 mm | One 4×8 ft sheet, cut in four | ₱450 | about ₱540 – ₱608 |
| Three booth panels 1.22 × 2.0 m, 3.0 mm | Three 4×8 ft sheets, cut | ₱1,350 | about ₱1,620 – ₱1,823 |
| Small-item display panels, 1×1 inch, 2.6 mm | One 4×8 ft sheet | ₱1,250 | Ask for a quote |
Frames, stands, hooks, paint or powder coating and labour are extra. Galvanizing adds about 20 to 35%. For other gauges, see the steel matting price list.
Tips for a Better Display
- Frame every panel. A flat bar or angle border keeps the panel flat and hides the cut ends.
- Test the hooks. Hang a typical load before you open. Heavy goods need a stronger frame or closer fixing points.
- Brace freestanding stalls. Use a wide base or a bottom rail, so a stall does not tip when customers lean on it.
- Pick the finish for the place. Paint or powder coat for indoor shops, and use galvanized for a stall that stands in the rain. See galvanized vs black iron.
- Plan for transport. Panels of 1.22 m width fold or stack flat for bazaars and fit in most vans.
Frequently Asked Questions
Can steel matting be used for a display rack?
Yes. A framed steel matting panel works as a wall grid, a shelf or a booth wall that holds hooks, baskets and signs.
What mesh is best for a wall grid display?
2×2 inch mesh in 3.0 mm wire for most goods, and 1×1 inch for small items.
Should a market stall use galvanized steel matting?
Yes, if the stall stands outdoors or gets wet. For indoor shops, paint or powder coat black iron.
Can you cut steel matting to my panel size?
We make custom sheet sizes. Send us the width and height of the panels you need.
Do you make the stands and frames?
We make and supply the steel matting. Ask your welder or carpenter for the frames and stands.
See also the shelf and rack ideas, steel matting sizes, custom steel matting and all steel matting uses.
Send us your display size, we quote the panels
Tell us the panel width and height, the mesh opening, the wire thickness and whether you want black iron or galvanized. We will reply with the price and what is in stock.
Get a Free Quote →