Can you make animal cages from steel matting?
Yes. Welded wire panels (steel matting) make strong cages for poultry, gamefowl, rabbits, dogs and cats. Cut the panels to size, join them with cage clips or wire, and fix them to a frame or legs. Pick the mesh opening by animal: 1×1 inch for small birds and chicks, 2×2 inch for adult chickens, gamefowl, rabbits and cats, and 2×2 inch in thicker wire for dogs. Use galvanized matting for anything outdoors or washed often.
Looking for a strong, easy-to-clean cage for chickens, gamefowl, rabbits, dogs or cats? Welded wire (steel matting) is stiff, so a cage keeps its shape, lets air through and hoses clean. This page shows six cage ideas, which mesh and wire suit each animal, what the matting costs, and what to tell us so we can supply the panels. We make the matting. The legs, frame and doors come from your welder, or you can build a small cage yourself with cage clips and a bolt cutter.
6 Steel Matting Animal Cage Ideas
1. Poultry or gamefowl cage
A single-bird or pair cage on legs, about 60 cm wide, 60 to 90 cm deep and 60 cm high, with a hinged front door and a tray or raised mesh floor so droppings fall through. 2×2 inch mesh in 2.6 mm wire is enough for most adult birds. One 4×8 ft sheet (1.22 m × 2.44 m) covers the six faces of a 60 cm cage with offcuts left over. Put the door where you can reach feed and water without lifting the cage.
2. Rabbit hutch
A hutch has mesh sides, a mesh floor and a solid roof that keeps off sun and rain. Use 1×1 inch mesh for the floor so feet do not catch, and 2×2 inch for the sides. Raise it 60 to 90 cm off the ground on legs, slope the roof so water runs off, and leave part of the floor solid, such as a wooden board, as a resting spot.
3. Dog kennel and run
A run of tall panels around a dog house. Use 2×2 inch mesh in 3.0 to 3.5 mm wire, and 4.5 mm for a large or strong dog. A 6×20 ft sheet (1.83 m high, 6 m long) gives panels tall enough that most dogs cannot jump out. Frame the panels in angle bar or pipe and put a roof over at least part of the run for shade.
4. Walk-in chicken or duck run
A walk-in run lets you stand inside to feed and clean. Build a pipe or wood frame about 1.8 m high and line it with 2×2 inch mesh, with 1×1 inch mesh (or chicken wire) on the lowest 60 cm if chicks, rats or snakes are a problem. Bury the bottom edge, or lay a skirt of mesh flat on the ground, so animals cannot dig in. Cover the top with mesh or roofing sheets.
5. Pigeon, lovebird and bird aviary
For small birds use a tight 1×1 inch mesh so they cannot squeeze through. An aviary is a larger walk-in cage with a mesh roof and a solid back wall for shelter. Use galvanized matting and wash it regularly. Ask your vet or breeder about the right wire spacing for the species you keep.
6. Cat enclosure for a balcony or garden
A mesh enclosure lets a cat enjoy fresh air without escaping. Use 2×2 inch mesh in 2.6 to 3.0 mm wire on a frame, with a mesh roof so the cat cannot climb out and a latch it cannot open. On a balcony, check the building rules first.
Which Mesh and Wire for Each Cage?
| Cage | Mesh opening | Wire | Notes |
|---|---|---|---|
| Poultry or gamefowl cage | 2×2 inch | 2.6 mm | 1×1 inch for chicks |
| Rabbit hutch | 1×1 floor, 2×2 sides | 2.6 – 3.0 mm | Solid roof, resting board |
| Dog run | 2×2 inch | 3.0 – 4.5 mm | Thicker wire for large dogs |
| Walk-in run | 2×2 inch (1×1 low) | 2.6 – 3.0 mm | Buried edge or skirt against digging |
| Bird aviary | 1×1 inch | 2.6 mm | Galvanized, wash regularly |
| Cat enclosure | 2×2 inch | 2.6 – 3.0 mm | Roof and a latch cats cannot open |
These are design suggestions, not veterinary or engineering advice. Check cage size and wire spacing for your animal with your vet or breeder. See the wire mesh gauge guide.
What the Matting Costs for a Cage
Only the matting is priced here. Using our October 2026 pick-up prices for black iron:
| Cage | Sheet used | Matting, black iron | Matting, galvanized |
|---|---|---|---|
| Poultry or gamefowl cage, 60 cm, 2×2 inch, 2.6 mm | One 4×8 ft sheet, with offcuts | ₱318 | about ₱382 – ₱429 |
| Rabbit hutch about 1.2 m long, 2×2 inch, 3.0 mm | One 4×8 ft sheet | ₱450 | about ₱540 – ₱608 |
| Dog run 2 × 3 m, 1.8 m high, no roof, 2×2 inch, 3.5 mm | Two 6×20 ft sheets, cut | ₱3,742 | about ₱4,490 – ₱5,052 |
| Bird aviary panels, 1×1 inch, 2.6 mm | One 4×8 ft sheet | ₱1,250 | Ask for a quote |
Legs, frame, doors, hinges, latches, trays, cage clips, paint or galvanizing and welding labour are extra. Galvanizing adds about 20 to 35%. For a very light, cheap enclosure, see chicken wire (4 ft high, 90 ft roll, ₱1,600). For other gauges, see the steel matting price list.
Tips for Building a Better Cage
- Use galvanized for anything wet. Droppings and wash water rust black iron quickly. Galvanized matting lasts about 10 to 20 years in the Philippine climate. See galvanized vs black iron.
- Smooth the cut ends. Cut wire ends are sharp. Border the panel with flat bar or angle, or bend and file the ends, so animals and hands are not hurt.
- Keep predators out. Rats, snakes, monitor lizards and stray dogs go after poultry and rabbits. Use a small mesh low down, fit a proper latch and close any gap bigger than a hand.
- Give shade and rain cover. A bare metal cage in full sun gets hot. Roof at least part of it.
- Plan for cleaning. A mesh floor over a removable tray makes cleaning quick. Make doors big enough to get a hand and a bowl through.
Frequently Asked Questions
Can steel matting be used for an animal cage?
Yes. Cut steel matting panels to size and join them with cage clips, wire or welding to a frame. Pick the mesh opening to suit the animal.
What mesh size is best for a chicken cage?
For adult birds, 2×2 inch mesh in 2.6 mm wire. For chicks and small birds, use 1×1 inch mesh or chicken wire.
Should an animal cage use black iron or galvanized steel matting?
Galvanized for cages that are outdoors or washed often. Black iron rusts quickly where droppings and water collect. If you use black iron, paint it well and repaint when the paint wears off.
Can you cut steel matting to the size of my cage?
We make custom sheet sizes. Send us the width and height of the panels you need. You can also cut standard sheets yourself with a bolt cutter, then paint or galvanize the cut edges.
Do you sell finished cages?
We make and supply the steel matting. Ask your welder or fabricator for the frame, legs, doors and trays.
See also the chicken wire guide, steel matting sizes, custom steel matting and all steel matting uses.
Send us your cage size, we quote the panels
Tell us the cage size, the animal, the mesh opening, the wire thickness and whether you want black iron or galvanized. We will reply with the price and what is in stock.
Get a Free Quote →